Kontrola disku gsmartcontrol

...

Moderátoři: Marfy, Mods_junior, Mods_senior, HW spec team

Uživatelský avatar
Akrej
Level 5.5
Level 5.5
Příspěvky: 2999
Registrován: červen 12
Pohlaví: Muž
Stav:
Offline

Kontrola disku gsmartcontrol

Příspěvekod Akrej » 15 kvě 2019 18:05

Zdravím

Nevim jaky je nejvhodnější nastroj pro linux na test disku ale zkusil jsem gsmartcontrol. A potřebuju vědět podle logu jestli je vše v pořadku není to jak crystal disk.

smartctl 6.5 2016-01-24 r4214 [i686-linux-4.4.0-146-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family: Hitachi Travelstar 5K100
Device Model: HTS541060G9AT00
Serial Number: MP26MBXCG2UJSH
Firmware Version: MB3OA60A
User Capacity: 60 011 642 880 bytes [60,0 GB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA/ATAPI-6 T13/1410D revision 3a
Local Time is: Wed May 15 17:22:41 2019 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 645) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 47) minutes.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 062 Pre-fail Always - 0
2 Throughput_Performance 0x0005 105 105 040 Pre-fail Offline - 4567
3 Spin_Up_Time 0x0007 222 222 033 Pre-fail Always - 2
4 Start_Stop_Count 0x0012 096 096 000 Old_age Always - 6759
5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail Always - 0
7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 124 124 040 Pre-fail Offline - 38
9 Power_On_Hours 0x0012 085 085 000 Old_age Always - 6673
10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 098 098 000 Old_age Always - 4068
191 G-Sense_Error_Rate 0x000a 100 100 000 Old_age Always - 0
192 Power-Off_Retract_Count 0x0032 099 099 000 Old_age Always - 204
193 Load_Cycle_Count 0x0012 080 080 000 Old_age Always - 207785
194 Temperature_Celsius 0x0002 171 171 000 Old_age Always - 32 (Min/Max 3/53)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 2
197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 0

SMART Error Log Version: 1
ATA Error Count: 51 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 51 occurred at disk power-on lifetime: 5116 hours (213 days + 4 hours)
When the command that caused the error occurred, the device was in standby mode.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 40 80 7c fc e6 Error: IDNF 64 sectors at LBA = 0x06fc7c80 = 117210240

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 40 80 7c fc e6 00 00:09:16.800 READ DMA
c8 00 08 e7 ba 2e e0 00 00:09:16.500 READ DMA
c8 00 40 80 7c fc e6 00 00:09:16.500 READ DMA
c8 00 08 df ba 2e e0 00 00:09:16.400 READ DMA
c8 00 40 80 7c fc e6 00 00:09:16.400 READ DMA

Error 50 occurred at disk power-on lifetime: 5116 hours (213 days + 4 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 40 80 7c fc e6 Error: IDNF 64 sectors at LBA = 0x06fc7c80 = 117210240

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 40 80 7c fc e6 00 00:09:16.500 READ DMA
c8 00 08 df ba 2e e0 00 00:09:16.400 READ DMA
c8 00 40 80 7c fc e6 00 00:09:16.400 READ DMA
c8 00 40 00 00 00 e0 00 00:09:16.400 READ DMA
c8 00 08 9f 2e 6e e1 00 00:09:16.400 READ DMA

Error 49 occurred at disk power-on lifetime: 5116 hours (213 days + 4 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 40 80 7c fc e6 Error: IDNF 64 sectors at LBA = 0x06fc7c80 = 117210240

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 40 80 7c fc e6 00 00:09:16.400 READ DMA
c8 00 40 00 00 00 e0 00 00:09:16.400 READ DMA
c8 00 08 9f 2e 6e e1 00 00:09:16.400 READ DMA
c8 00 40 7f e6 3b e2 00 00:09:16.400 READ DMA
c8 00 40 bf e6 3b e2 00 00:09:16.400 READ DMA

Error 48 occurred at disk power-on lifetime: 5114 hours (213 days + 2 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 40 80 7c fc e6 Error: IDNF 64 sectors at LBA = 0x06fc7c80 = 117210240

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 40 80 7c fc e6 00 00:09:19.600 READ DMA
c8 00 40 80 7c fc e6 00 00:09:19.600 READ DMA
c8 00 40 80 7c fc e6 00 00:09:19.500 READ DMA
c8 00 40 00 00 00 e0 00 00:09:19.500 READ DMA
c8 00 10 1f e2 cd e6 00 00:09:19.500 READ DMA

Error 47 occurred at disk power-on lifetime: 5114 hours (213 days + 2 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 40 80 7c fc e6 Error: IDNF 64 sectors at LBA = 0x06fc7c80 = 117210240

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 40 80 7c fc e6 00 00:09:19.600 READ DMA
c8 00 40 80 7c fc e6 00 00:09:19.500 READ DMA
c8 00 40 00 00 00 e0 00 00:09:19.500 READ DMA
c8 00 10 1f e2 cd e6 00 00:09:19.500 READ DMA
c8 00 01 e0 e1 cd e6 00 00:09:19.500 READ DMA

SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 6673 -

Warning! SMART Selective Self-Test Log Structure error: invalid SMART checksum.
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
"Nejsem nerozumný. Jen nemám ten samý rozum jako vy."
Diogénes ze Sinopé
-------------------------------------
„Mějte dobrou náladu. Dobrá nálada vaše problémy sice nevyřeší, ale naštve tolik lidí kolem, že stojí za to si ji užít.“
Jan Werich
--------------------------------------
Snažím se psát bez chyb
-------------------------

Reklama
  • Mohlo by vás zajímat
    Odpovědi
    Zobrazení
    Poslední příspěvek
  • 100% využitie disku Příloha(y)
    od krakenus600 » 10 zář 2023 19:47 » v Vše ostatní (sw)
    9
    2663
    od krakenus600 Zobrazit poslední příspěvek
    11 zář 2023 11:26
  • Více OS na jednom disku
    od fafejt » 18 dub 2023 23:54 » v Windows 11, 10, 8...
    7
    1476
    od petr22 Zobrazit poslední příspěvek
    19 dub 2023 09:10
  • Pomoc s výběrem SSD disku
    od eli125 » 25 dub 2023 12:37 » v Rady s výběrem hw a sestavením PC
    1
    1179
    od Zivan Zobrazit poslední příspěvek
    25 dub 2023 15:07
  • Jak zobrazit soubory z ostatních disků.
    od xDwery » 24 kvě 2023 06:05 » v Problémy s hardwarem
    1
    497
    od ITCrowd Zobrazit poslední příspěvek
    24 kvě 2023 06:26
  • Jak zobrazit soubory z ostatních disků Příloha(y)
    od xDwery » 24 kvě 2023 14:57 » v Problémy s hardwarem
    2
    604
    od xDwery Zobrazit poslední příspěvek
    24 kvě 2023 20:09

Zpět na “Vše ostatní (hw)”

Kdo je online

Uživatelé prohlížející si toto fórum: Žádní registrovaní uživatelé a 13 hostů