PC-HELP.CZ

Na stolním pc (os - linux ubuntu) , které je připojeno k modemu přes kabel USB (vím, že to není chytrý, ale doteď to fungovalo, tak jsem to neřešila), mi nejede net. Přitom mám připojený ntb přes wifi a ta šlape v pohodě. Prostě ho OS stolního pc nevidí, nenačte.. já nevím. Zkoušela jsem už snad všechno - připojit kabel do ntb, ale to funguje.
Prohledávám fóra už druhý den, ale pořád nic. Teoreticky si myslím, že vím, jak problém řešit, ale prakticky jsem úplně ztracená (nainstalovat nový catche a nejlíp připojit stolní pc přes wifi - nicméně nemám páru jak).

Budu vděčná za jakoukoli radu! :) Díky.

Jestli chceš připojit stolní pc přes wifi. Doporučuji tento USB WiFi

--- Doplnění předchozího příspěvku (03 Čer 2013 14:56) ---

Používám ho už půl roku a nemám s tím žádný problém.

Ak sa ti nahodou updatoval OS, je mozne, ze sa updatoval ovladac pre modem, ktory pouzivas. A ten novy ovladac potrebuje bud donastavit, alebo uz nefunguje s tvojim modemom.
Hod sem vypis prikazov:
1: lsusb
2: ifconfig
3: dmesg

Tiez je potrebne uviest presny typ modemu USB a verziu OS
Verzia OS sa zisti prikazom: uname -a
Typ modemu bude najskor na stitku (zvycajne zospodu)

Jen doplním, že vlastním totožnou externí wifi kartu a mě způsobovala aplikace od tp linku samovolné minimalizování při hraní takže nainstaluj jen ovladače.. já musel přeinstalovat OS, jsem si myslel, že to způsobuje vir až pak jsem na to přišel :)

modsuissy - děkuju za tip :). Popřemýšlím o tom! :)

Wordstar14: Na to jsem nepomyslela, ale nejspíš máš pravdu

Výpis:
1:
Bus 002 Device 002: ID 0586:3309 ZyXEL Communications Corp. ADSL Modem Prestige 600 series
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
2:
lo Link encap:Místní smyčka
inet adr:127.0.0.1 Maska:255.0.0.0
inet6-adr: ::1/128 Rozsah:Počítač
AKTIVOVÁNO SMYČKA BĚŽÍ MTU:16436 Metrika:1
RX packets:44 errors:0 dropped:0 overruns:0 frame:0
TX packets:44 errors:0 dropped:0 overruns:0 carrier:0
kolizí:0 délka odchozí fronty:0
Přijato bajtů: 4416 (4.4 KB) Odesláno bajtů: 4416 (4.4 KB)
-> což je trochu divné, včera tam byly ty připojení 3

3:
[ 0.253786] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.260270] fuse init (API version 7.13)
[ 0.260394] msgmni has been set to 1716
[ 0.260630] alg: No test for stdrng (krng)
[ 0.260692] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 0.260695] io scheduler noop registered
[ 0.260697] io scheduler anticipatory registered
[ 0.260699] io scheduler deadline registered
[ 0.260740] io scheduler cfq registered (default)
[ 0.260865] alloc irq_desc for 24 on node -1
[ 0.260868] alloc kstat_irqs on node -1
[ 0.260876] pcieport 0000:00:0b.0: irq 24 for MSI/MSI-X
[ 0.260881] pcieport 0000:00:0b.0: setting latency timer to 64
[ 0.260956] alloc irq_desc for 25 on node -1
[ 0.260958] alloc kstat_irqs on node -1
[ 0.260963] pcieport 0000:00:0c.0: irq 25 for MSI/MSI-X
[ 0.260967] pcieport 0000:00:0c.0: setting latency timer to 64
[ 0.261031] alloc irq_desc for 26 on node -1
[ 0.261033] alloc kstat_irqs on node -1
[ 0.261037] pcieport 0000:00:0d.0: irq 26 for MSI/MSI-X
[ 0.261041] pcieport 0000:00:0d.0: setting latency timer to 64
[ 0.261105] alloc irq_desc for 27 on node -1
[ 0.261107] alloc kstat_irqs on node -1
[ 0.261111] pcieport 0000:00:0e.0: irq 27 for MSI/MSI-X
[ 0.261115] pcieport 0000:00:0e.0: setting latency timer to 64
[ 0.261179] alloc irq_desc for 28 on node -1
[ 0.261181] alloc kstat_irqs on node -1
[ 0.261188] pcieport 0000:00:0f.0: irq 28 for MSI/MSI-X
[ 0.261192] pcieport 0000:00:0f.0: setting latency timer to 64
[ 0.261246] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 0.261270] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 0.261376] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0
[ 0.261380] ACPI: Power Button [PWRB]
[ 0.261431] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
[ 0.261433] ACPI: Power Button [PWRF]
[ 0.261742] processor LNXCPU:00: registered as cooling_device0
[ 0.269535] isapnp: Scanning for PnP cards...
[ 0.275180] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 0.275281] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 0.275372] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 0.275605] 00:05: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 0.276734] brd: module loaded
[ 0.277210] loop: module loaded
[ 0.277296] input: Macintosh mouse button emulation as /devices/virtual/input/input2
[ 0.277481] pata_acpi 0000:00:04.0: setting latency timer to 64
[ 0.277837] ACPI: PCI Interrupt Link [LSA0] enabled at IRQ 21
[ 0.277843] alloc irq_desc for 21 on node -1
[ 0.277845] alloc kstat_irqs on node -1
[ 0.277855] pata_acpi 0000:00:05.0: PCI INT A -> Link[LSA0] -> GSI 21 (level, low) -> IRQ 21
[ 0.277871] pata_acpi 0000:00:05.0: setting latency timer to 64
[ 0.277878] pata_acpi 0000:00:05.0: PCI INT A disabled
[ 0.278162] ACPI: PCI Interrupt Link [LSA1] enabled at IRQ 20
[ 0.278164] alloc irq_desc for 20 on node -1
[ 0.278166] alloc kstat_irqs on node -1
[ 0.278173] pata_acpi 0000:00:05.1: PCI INT B -> Link[LSA1] -> GSI 20 (level, low) -> IRQ 20
[ 0.278189] pata_acpi 0000:00:05.1: setting latency timer to 64
[ 0.278195] pata_acpi 0000:00:05.1: PCI INT B disabled
[ 0.278509] Fixed MDIO Bus: probed
[ 0.278544] PPP generic driver version 2.4.2
[ 0.278580] tun: Universal TUN/TAP device driver, 1.6
[ 0.278582] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 0.278661] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.278673] ehci_hcd 0000:00:02.1: PCI INT B -> Link[LUB2] -> GSI 22 (level, low) -> IRQ 22
[ 0.278689] ehci_hcd 0000:00:02.1: setting latency timer to 64
[ 0.278691] ehci_hcd 0000:00:02.1: EHCI Host Controller
[ 0.278725] ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 1
[ 0.278753] ehci_hcd 0000:00:02.1: debug port 1
[ 0.278760] ehci_hcd 0000:00:02.1: cache line size of 64 is not supported
[ 0.278781] ehci_hcd 0000:00:02.1: irq 22, io mem 0xfbefac00
[ 0.327593] ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00
[ 0.327727] usb usb1: configuration #1 chosen from 1 choice
[ 0.327757] hub 1-0:1.0: USB hub found
[ 0.327770] hub 1-0:1.0: 10 ports detected
[ 0.327840] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 0.327861] ohci_hcd 0000:00:02.0: PCI INT A -> Link[LUB0] -> GSI 23 (level, low) -> IRQ 23
[ 0.327879] ohci_hcd 0000:00:02.0: setting latency timer to 64
[ 0.327882] ohci_hcd 0000:00:02.0: OHCI Host Controller
[ 0.327917] ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2
[ 0.327948] ohci_hcd 0000:00:02.0: irq 23, io mem 0xfbefb000
[ 0.417524] usb usb2: configuration #1 chosen from 1 choice
[ 0.417555] hub 2-0:1.0: USB hub found
[ 0.417567] hub 2-0:1.0: 10 ports detected
[ 0.417643] uhci_hcd: USB Universal Host Controller Interface driver
[ 0.417738] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
[ 0.425285] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 0.425294] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 0.425459] mice: PS/2 mouse device common for all mice
[ 0.425589] rtc_cmos 00:02: RTC can wake from S4
[ 0.425631] rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
[ 0.425661] rtc0: alarms up to one year, y3k, 114 bytes nvram
[ 0.425792] device-mapper: uevent: version 1.0.3
[ 0.425908] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
[ 0.428309] device-mapper: multipath: version 1.1.0 loaded
[ 0.428313] device-mapper: multipath round-robin: version 1.0.0 loaded
[ 0.428485] EISA: Probing bus 0 at eisa.0
[ 0.428494] Cannot allocate resource for EISA slot 2
[ 0.428509] EISA: Detected 0 cards.
[ 0.430474] cpuidle: using governor ladder
[ 0.430477] cpuidle: using governor menu
[ 0.430885] TCP cubic registered
[ 0.431054] NET: Registered protocol family 10
[ 0.431783] NET: Registered protocol family 17
[ 0.431815] powernow-k8: Found 1 AMD Athlon(tm) 64 Processor 3200+ processors (1 cpu cores) (version 2.20.00)
[ 0.434314] [Firmware Bug]: powernow-k8: No PSB or ACPI _PSS objects
[ 0.436204] Using IPI No-Shortcut mode
[ 0.436303] PM: Resume from disk failed.
[ 0.436316] registered taskstats version 1
[ 0.436611] Magic number: 1:648:347
[ 0.436665] pci0000:00: hash matches
[ 0.436721] rtc_cmos 00:02: setting system clock to 2013-06-02 21:19:40 UTC (1370207980)
[ 0.436724] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 0.436726] EDD information not available.
[ 0.445759] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input3
[ 0.703605] Freeing initrd memory: 7823k freed
[ 0.839976] isapnp: No Plug & Play device found
[ 0.839994] Freeing unused kernel memory: 664k freed
[ 0.840573] Write protecting the kernel text: 4704k
[ 0.840604] Write protecting the kernel read-only data: 1848k
[ 0.859896] udev: starting version 151
[ 1.044042] usb 2-5: new full speed USB device using ohci_hcd and address 2
[ 1.062881] forcedeth: Reverse Engineered nForce ethernet driver. Version 0.64.
[ 1.063225] ACPI: PCI Interrupt Link [LMAC] enabled at IRQ 23
[ 1.063231] forcedeth 0000:00:08.0: PCI INT A -> Link[LMAC] -> GSI 23 (level, low) -> IRQ 23
[ 1.063237] forcedeth 0000:00:08.0: setting latency timer to 64
[ 1.063279] nv_probe: set workaround bit for reversed mac addr
[ 1.085808] Floppy drive(s): fd0 is 1.44M
[ 1.103917] FDC 0 is a post-1991 82077
[ 1.313504] usb 2-5: configuration #1 chosen from 1 choice
[ 1.581810] forcedeth 0000:00:08.0: ifname eth0, PHY OUI 0x1c1 @ 1, addr 00:16:17:76:97:f4
[ 1.581815] forcedeth 0000:00:08.0: highdma csum vlan pwrctl mgmt gbit lnktim msi desc-v3
[ 1.581838] pata_amd 0000:00:04.0: version 0.4.1
[ 1.581882] pata_amd 0000:00:04.0: setting latency timer to 64
[ 1.582311] scsi0 : pata_amd
[ 1.582461] scsi1 : pata_amd
[ 1.626111] ata1: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14
[ 1.626115] ata2: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15
[ 1.626238] sata_nv 0000:00:05.0: version 3.5
[ 1.626248] sata_nv 0000:00:05.0: PCI INT A -> Link[LSA0] -> GSI 21 (level, low) -> IRQ 21
[ 1.626251] sata_nv 0000:00:05.0: Using SWNCQ mode
[ 1.626298] sata_nv 0000:00:05.0: setting latency timer to 64
[ 1.626594] scsi2 : sata_nv
[ 1.626695] scsi3 : sata_nv
[ 1.627825] ata3: SATA max UDMA/133 cmd 0xd800 ctl 0xd480 bmdma 0xd000 irq 21
[ 1.627828] ata4: SATA max UDMA/133 cmd 0xd400 ctl 0xd080 bmdma 0xd008 irq 21
[ 1.627850] sata_nv 0000:00:05.1: PCI INT B -> Link[LSA1] -> GSI 20 (level, low) -> IRQ 20
[ 1.627852] sata_nv 0000:00:05.1: Using SWNCQ mode
[ 1.627896] sata_nv 0000:00:05.1: setting latency timer to 64
[ 1.628181] scsi4 : sata_nv
[ 1.628422] scsi5 : sata_nv
[ 1.629542] ata5: SATA max UDMA/133 cmd 0xcc00 ctl 0xc880 bmdma 0xc400 irq 20
[ 1.629546] ata6: SATA max UDMA/133 cmd 0xc800 ctl 0xc480 bmdma 0xc408 irq 20
[ 1.788265] ata1.00: ATAPI: HL-DT-ST DVDRAM GSA-H10N, JL10, max UDMA/33
[ 1.788292] ata1: nv_mode_filter: 0x739f&0x739f->0x739f, BIOS=0x7000 (0xc0000000) ACPI=0x701f (60:900:0x11)
[ 1.804211] ata1.00: configured for UDMA/33
[ 1.809916] scsi 0:0:0:0: CD-ROM HL-DT-ST DVDRAM GSA-H10N JL10 PQ: 0 ANSI: 5
[ 1.822316] sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
[ 1.822319] Uniform CD-ROM driver Revision: 3.20
[ 1.822540] sr 0:0:0:0: Attached scsi CD-ROM sr0
[ 1.822649] sr 0:0:0:0: Attached scsi generic sg0 type 5
[ 1.822749] ata2: port disabled. ignoring.
[ 1.940027] ata5: SATA link down (SStatus 0 SControl 300)
[ 2.096030] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 2.138768] ata3.00: ATA-7: ST3250820AS, 3.AAD, max UDMA/133
[ 2.138771] ata3.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 2.205422] ata3.00: configured for UDMA/133
[ 2.205504] scsi 2:0:0:0: Direct-Access ATA ST3250820AS 3.AA PQ: 0 ANSI: 5
[ 2.205629] sd 2:0:0:0: Attached scsi generic sg1 type 0
[ 2.205811] sd 2:0:0:0: [sda] 488397168 512-byte logical blocks: (250 GB/232 GiB)
[ 2.205853] sd 2:0:0:0: [sda] Write Protect is off
[ 2.205856] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 2.205878] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2.205999] sda: sda1 sda2 < sda5 >
[ 2.265458] sd 2:0:0:0: [sda] Attached SCSI disk
[ 2.516025] ata4: SATA link down (SStatus 0 SControl 300)
[ 2.828024] ata6: SATA link down (SStatus 0 SControl 300)
[ 3.098034] kjournald starting. Commit interval 5 seconds
[ 3.098045] EXT3-fs: mounted filesystem with ordered data mode.
[ 24.087220] Adding 3004112k swap on /dev/sda5. Priority:-1 extents:1 across:3004112k
[ 24.121270] udev: starting version 151
[ 24.230223] i2c i2c-0: nForce2 SMBus adapter at 0x2d00
[ 24.230244] i2c i2c-1: nForce2 SMBus adapter at 0x2e00
[ 24.278846] lp: driver loaded but no devices found
[ 24.476475] Linux agpgart interface v0.103
[ 24.506278] k8temp 0000:00:18.3: Temperature readouts might be wrong - check erratum #141
[ 24.617666] parport_pc 00:08: reported by Plug and Play ACPI
[ 24.617712] parport0: PC-style at 0x378, irq 7 [PCSPP]
[ 24.674360] EXT3 FS on sda1, internal journal
[ 24.692883] type=1505 audit(1370208004.563:2): operation="profile_load" pid=604 name="/sbin/dhclient3"
[ 24.693182] type=1505 audit(1370208004.563:3): operation="profile_load" pid=604 name="/usr/lib/NetworkManager/nm-dhcp-client.action"
[ 24.693351] type=1505 audit(1370208004.563:4): operation="profile_load" pid=604 name="/usr/lib/connman/scripts/dhclient-script"
[ 24.710326] psmouse serio1: ID: 10 00 64
[ 24.710958] [drm] Initialized drm 1.1.0 20060810
[ 24.716642] lp0: using parport0 (interrupt-driven).
[ 24.719168] Linux video capture interface: v2.00
[ 24.763783] ppdev: user-space parallel port driver
[ 24.828340] usbcore: registered new interface driver cdc_ether
[ 24.906902] ACPI: PCI Interrupt Link [LNEB] enabled at IRQ 19
[ 24.906909] alloc irq_desc for 19 on node -1
[ 24.906912] alloc kstat_irqs on node -1
[ 24.906923] nouveau 0000:06:00.0: PCI INT A -> Link[LNEB] -> GSI 19 (level, low) -> IRQ 19
[ 24.906928] nouveau 0000:06:00.0: setting latency timer to 64
[ 24.921148] [drm] nouveau 0000:06:00.0: Detected an NV40 generation card (0x04b200a2)
[ 24.921586] [drm] nouveau 0000:06:00.0: Attempting to load BIOS image from PROM
[ 25.126462] [drm] nouveau 0000:06:00.0: ... appears to be valid
[ 25.126466] [drm] nouveau 0000:06:00.0: BIT BIOS found
[ 25.126469] [drm] nouveau 0000:06:00.0: Bios version 05.73.22.16
[ 25.126473] [drm] nouveau 0000:06:00.0: TMDS table script pointers not stubbed
[ 25.126476] [drm] nouveau 0000:06:00.0: BIT table 'd' not found
[ 25.126479] [drm] nouveau 0000:06:00.0: Found Display Configuration Block version 3.0
[ 25.126483] [drm] nouveau 0000:06:00.0: DCB connector table: VHER 0x30 5 10 2
[ 25.126487] [drm] nouveau 0000:06:00.0: 0: 0x00001030: type 0x30 idx 0 tag 0x07
[ 25.126490] [drm] nouveau 0000:06:00.0: 1: 0x00000100: type 0x00 idx 1 tag 0xff
[ 25.126493] [drm] nouveau 0000:06:00.0: 2: 0x00000210: type 0x10 idx 2 tag 0xff
[ 25.126496] [drm] nouveau 0000:06:00.0: 3: 0x00000211: type 0x11 idx 2 tag 0xff
[ 25.126499] [drm] nouveau 0000:06:00.0: 4: 0x00000213: type 0x13 idx 2 tag 0xff
[ 25.126503] [drm] nouveau 0000:06:00.0: Raw DCB entry 0: 01000300 00000028
[ 25.126506] [drm] nouveau 0000:06:00.0: Raw DCB entry 1: 03000302 00000000
[ 25.126509] [drm] nouveau 0000:06:00.0: Raw DCB entry 2: 04011310 00000028
[ 25.126512] [drm] nouveau 0000:06:00.0: Raw DCB entry 3: 04011312 00000000
[ 25.126515] [drm] nouveau 0000:06:00.0: Raw DCB entry 4: 020223f1 00c0c080
[ 25.126522] [drm] nouveau 0000:06:00.0: Parsing VBIOS init table 0 at offset 0xDF5D
[ 25.126600] [drm] nouveau 0000:06:00.0: Parsing VBIOS init table 1 at offset 0xE59E
[ 25.152678] saa7130/34: v4l2 driver version 0.2.15 loaded
[ 25.153089] ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 18
[ 25.153095] alloc irq_desc for 18 on node -1
[ 25.153097] alloc kstat_irqs on node -1
[ 25.153108] saa7134 0000:01:00.0: PCI INT A -> Link[LNKA] -> GSI 18 (level, low) -> IRQ 18
[ 25.153115] saa7133[0]: found at 0000:01:00.0, rev: 209, irq: 18, latency: 64, mmio: 0xfbfff800
[ 25.153122] saa7133[0]: subsystem: 1043:4876, board: ASUSTeK P7131 Hybrid [card=112,autodetected]
[ 25.153144] saa7133[0]: board init: gpio is 0
[ 25.153372] input: saa7134 IR (ASUSTeK P7131 Hybri as /devices/pci0000:00/0000:00:06.0/0000:01:00.0/input/input4
[ 25.153503] IRQ 18/saa7133[0]: IRQF_DISABLED is not guaranteed on shared IRQs
[ 25.307160] eth1: register 'rndis_host' at usb-0000:00:02.0-5, RNDIS device, 00:13:49:cc:88:27
[ 25.307185] usbcore: registered new interface driver rndis_host
[ 25.309024] ACPI: PCI Interrupt Link [LAZA] enabled at IRQ 22
[ 25.309032] HDA Intel 0000:00:06.1: PCI INT B -> Link[LAZA] -> GSI 22 (level, low) -> IRQ 22
[ 25.309036] hda_intel: Disable MSI for Nvidia chipset
[ 25.309064] HDA Intel 0000:00:06.1: setting latency timer to 64
[ 25.312029] saa7133[0]: i2c eeprom 00: 43 10 76 48 54 20 1c 00 43 43 a9 1c 55 d2 b2 92
[ 25.312039] saa7133[0]: i2c eeprom 10: ff ff ff 0f ff 20 ff ff ff ff ff ff ff ff ff ff
[ 25.312047] saa7133[0]: i2c eeprom 20: 01 40 01 02 03 01 01 03 08 ff 00 d5 ff ff ff ff
[ 25.312055] saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[ 25.312064] saa7133[0]: i2c eeprom 40: ff 21 00 c2 96 10 03 32 55 50 ff ff ff ff ff ff
[ 25.312072] saa7133[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[ 25.312080] saa7133[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[ 25.312088] saa7133[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[ 25.312097] saa7133[0]: i2c eeprom 80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[ 25.312105] saa7133[0]: i2c eeprom 90: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[ 25.312113] saa7133[0]: i2c eeprom a0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[ 25.312121] saa7133[0]: i2c eeprom b0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[ 25.312129] saa7133[0]: i2c eeprom c0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[ 25.312138] saa7133[0]: i2c eeprom d0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[ 25.312146] saa7133[0]: i2c eeprom e0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[ 25.312154] saa7133[0]: i2c eeprom f0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[ 25.312164] i2c i2c-2: Invalid 7-bit address 0x7a
[ 25.319680] input: ImPS/2 Generic Wheel Mouse as /devices/platform/i8042/serio1/input/input5
[ 25.348046] [drm] nouveau 0000:06:00.0: Parsing VBIOS init table 2 at offset 0xECAF
[ 25.348069] [drm] nouveau 0000:06:00.0: Parsing VBIOS init table 3 at offset 0xEE2F
[ 25.385897] [drm] nouveau 0000:06:00.0: Parsing VBIOS init table 4 at offset 0xF01D
[ 25.400170] tuner 2-004b: chip found @ 0x96 (saa7133[0])
[ 25.408651] [TTM] Zone kernel: Available graphics memory: 443574 kiB.
[ 25.408654] [TTM] Zone highmem: Available graphics memory: 513114 kiB.
[ 25.408668] [drm] nouveau 0000:06:00.0: 256 MiB VRAM
[ 25.409447] [drm] nouveau 0000:06:00.0: 64 MiB GART (aperture)
[ 25.409656] [drm] nouveau 0000:06:00.0: Allocating FIFO number 0
[ 25.410893] [drm] nouveau 0000:06:00.0: nouveau_channel_alloc: initialised FIFO 0
[ 25.410901] [drm] nouveau 0000:06:00.0: Initial CRTC_OWNER is 0
[ 25.410907] [drm] nouveau 0000:06:00.0: Saving VGA fonts
[ 25.466565] cfg80211: Calling CRDA to update world regulatory domain
[ 25.499140] [drm] nouveau 0000:06:00.0: Detected a DVI-I connector
[ 25.499395] [drm] nouveau 0000:06:00.0: Detected a DVI-I connector
[ 25.499551] [drm] nouveau 0000:06:00.0: Detected a TV connector
[ 25.501123] [drm] nouveau 0000:06:00.0: Setting dpms mode 3 on vga encoder (output 0)
[ 25.501128] [drm] nouveau 0000:06:00.0: Setting dpms mode 3 on tmds encoder (output 1)
[ 25.501131] [drm] nouveau 0000:06:00.0: Setting dpms mode 3 on vga encoder (output 2)
[ 25.501134] [drm] nouveau 0000:06:00.0: Setting dpms mode 3 on tmds encoder (output 3)
[ 25.501137] [drm] nouveau 0000:06:00.0: Setting dpms mode 3 on TV encoder (output 4)
[ 25.540041] tda829x 2-004b: setting tuner address to 61
[ 25.541412] usbcore: registered new interface driver rndis_wlan
[ 25.586035] type=1505 audit(1370208005.563:5): operation="profile_load" pid=767 name="/usr/share/gdm/guest-session/Xsession"
[ 25.599900] type=1505 audit(1370208005.563:6): operation="profile_replace" pid=769 name="/sbin/dhclient3"
[ 25.604244] type=1505 audit(1370208005.563:7): operation="profile_replace" pid=769 name="/usr/lib/NetworkManager/nm-dhcp-client.action"
[ 25.604420] type=1505 audit(1370208005.563:8): operation="profile_replace" pid=769 name="/usr/lib/connman/scripts/dhclient-script"
[ 25.628267] type=1505 audit(1370208005.563:9): operation="profile_load" pid=770 name="/usr/bin/evince"
[ 25.643109] tda829x 2-004b: type set to tda8290+75a
[ 25.652368] type=1505 audit(1370208005.563:10): operation="profile_load" pid=770 name="/usr/bin/evince-previewer"
[ 25.654792] type=1505 audit(1370208005.563:11): operation="profile_load" pid=770 name="/usr/bin/evince-thumbnailer"
[ 25.745298] cfg80211: World regulatory domain updated:
[ 25.745302] (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 25.745306] (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 25.745309] (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 25.745312] (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 25.745315] (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 25.745318] (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 25.816252] [drm] nouveau 0000:06:00.0: allocated 1280x1024 fb: 0x49000, bo ef9c2e00
[ 25.816347] fb0: nouveaufb frame buffer device
[ 25.816349] registered panic notifier
[ 25.816355] [drm] Initialized nouveau 0.0.15 20090420 for 0000:06:00.0 on minor 0
[ 25.818323] vga16fb: initializing
[ 25.818327] vga16fb: mapped to 0xc00a0000
[ 25.818332] vga16fb: not registering due to another framebuffer present
[ 25.873340] [drm] nouveau 0000:06:00.0: Setting dpms mode 0 on vga encoder (output 2)
[ 25.873346] [drm] nouveau 0000:06:00.0: Output DVI-I-2 is running on CRTC 0 using output C
[ 25.905517] Console: switching to colour frame buffer device 160x64
[ 26.022163] apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
[ 26.022167] apm: overridden by ACPI.
[ 26.036131] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:06.1/input/input6
[ 27.204241] [drm] nouveau 0000:06:00.0: Allocating FIFO number 1
[ 27.205465] [drm] nouveau 0000:06:00.0: nouveau_channel_alloc: initialised FIFO 1
[ 29.572261] saa7133[0]: registered device video0 [v4l2]
[ 29.572297] saa7133[0]: registered device vbi0
[ 29.572325] saa7133[0]: registered device radio0
[ 29.604461] saa7134 ALSA driver for DMA sound loaded
[ 29.604477] IRQ 18/saa7133[0]: IRQF_DISABLED is not guaranteed on shared IRQs
[ 29.604498] saa7133[0]/alsa: saa7133[0] at 0xfbfff800 irq 18 registered as card -2
[ 29.695993] dvb_init() allocating 1 frontend
[ 29.928149] DVB: registering new adapter (saa7133[0])
[ 29.928155] DVB: registering adapter 0 frontend 0 (Philips TDA10046H DVB-T)...
[ 30.156022] tda1004x: setting up plls for 48MHz sampling clock
[ 32.420078] tda1004x: timeout waiting for DSP ready
[ 32.460025] tda1004x: found firmware revision 0 -- invalid
[ 32.460029] tda1004x: trying to boot from eeprom
[ 34.772015]
[ 34.772019] floppy driver state
[ 34.772020] -------------------
[ 34.772024] now=4294900989 last interrupt=4294892572 diff=8417 last called handler=f80965b0
[ 34.772027] timeout_message=lock fdc
[ 34.772028] last output bytes:
[ 34.772030] 8 80 4294892567
[ 34.772032] 8 80 4294892567
[ 34.772033] 8 80 4294892567
[ 34.772035] 8 80 4294892571
[ 34.772037] 8 80 4294892571
[ 34.772038] 8 80 4294892571
[ 34.772040] 8 80 4294892571
[ 34.772042] e 80 4294892571
[ 34.772044] 13 80 4294892571
[ 34.772045] 0 90 4294892571
[ 34.772047] 1a 90 4294892571
[ 34.772049] 0 90 4294892571
[ 34.772050] 12 90 4294892571
[ 34.772052] 0 90 4294892571
[ 34.772054] 14 90 4294892571
[ 34.772055] 18 80 4294892571
[ 34.772057] 8 80 4294892572
[ 34.772059] 8 80 4294892572
[ 34.772060] 8 80 4294892572
[ 34.772062] 8 80 4294892572
[ 34.772063] last result at 4294892572
[ 34.772065] last redo_fd_request at 4294892572
[ 34.772067]
[ 34.772077] status=80
[ 34.772078] fdc_busy=1
[ 34.772079] floppy_work.func=f809ace0
[ 34.772081] cont=f809d950
[ 34.772083] current_req=(null)
[ 34.772084] command_status=-1
[ 34.772086]
[ 34.772088] floppy0: floppy timeout called
[ 34.784020] tda1004x: timeout waiting for DSP ready
[ 34.824020] tda1004x: found firmware revision 0 -- invalid
[ 34.824023] tda1004x: waiting for firmware upload...
[ 34.824029] saa7134 0000:01:00.0: firmware: requesting dvb-fe-tda10046.fw
[ 34.865703] saa7134 0000:01:00.0: firmware: requesting dvb-fe-tda10045.fw
[ 34.870066] tda1004x: no firmware upload (timeout or file not found?)
[ 34.870071] tda1004x: firmware upload failed
[ 329.916031] usb 1-7: new high speed USB device using ehci_hcd and address 3
[ 330.049335] usb 1-7: configuration #1 chosen from 1 choice
[ 330.089472] Initializing USB Mass Storage driver...
[ 330.089590] scsi6 : SCSI emulation for USB Mass Storage devices
[ 330.089744] usbcore: registered new interface driver usb-storage
[ 330.089747] USB Mass Storage support registered.
[ 330.097354] usb-storage: device found at 3
[ 330.097357] usb-storage: waiting for device to settle before scanning
[ 335.096141] usb-storage: device scan complete
[ 335.097752] scsi 6:0:0:0: Direct-Access SanDisk Cruzer Pattern 8.01 PQ: 0 ANSI: 0 CCS
[ 335.098107] scsi 6:0:0:1: CD-ROM SanDisk Cruzer Pattern 8.01 PQ: 0 ANSI: 0
[ 335.100608] sd 6:0:0:0: Attached scsi generic sg2 type 0
[ 335.103108] sd 6:0:0:0: [sdb] 15695871 512-byte logical blocks: (8.03 GB/7.48 GiB)
[ 335.106914] sd 6:0:0:0: [sdb] Write Protect is off
[ 335.106920] sd 6:0:0:0: [sdb] Mode Sense: 45 00 00 08
[ 335.106923] sd 6:0:0:0: [sdb] Assuming drive cache: write through
[ 335.110302] sr1: scsi3-mmc drive: 48x/48x tray
[ 335.110562] sr 6:0:0:1: Attached scsi CD-ROM sr1
[ 335.110986] sr 6:0:0:1: Attached scsi generic sg3 type 5
[ 335.119520] sd 6:0:0:0: [sdb] Assuming drive cache: write through
[ 335.119528] sdb: sdb1
[ 335.123777] sd 6:0:0:0: [sdb] Assuming drive cache: write through
[ 335.123784] sd 6:0:0:0: [sdb] Attached SCSI removable disk
[ 335.341851] sr 6:0:0:1: [sr1] Unhandled sense code
[ 335.341856] sr 6:0:0:1: [sr1] Result: hostbyte=DID_ERROR driverbyte=DRIVER_SENSE
[ 335.341861] sr 6:0:0:1: [sr1] Sense Key : Hardware Error [current]
[ 335.341865] sr 6:0:0:1: [sr1] Add. Sense: No additional sense information
[ 335.341870] sr 6:0:0:1: [sr1] CDB: Read(10): 28 00 00 00 bf c0 00 00 02 00
[ 335.341879] end_request: I/O error, dev sr1, sector 196352
[ 335.341884] __ratelimit: 9 callbacks suppressed
[ 335.341887] Buffer I/O error on device sr1, logical block 49088
[ 335.341891] Buffer I/O error on device sr1, logical block 49089
[ 335.369851] sr 6:0:0:1: [sr1] Unhandled sense code
[ 335.369856] sr 6:0:0:1: [sr1] Result: hostbyte=DID_ERROR driverbyte=DRIVER_SENSE
[ 335.369860] sr 6:0:0:1: [sr1] Sense Key : Hardware Error [current]
[ 335.369865] sr 6:0:0:1: [sr1] Add. Sense: No additional sense information
[ 335.369870] sr 6:0:0:1: [sr1] CDB: Read(10): 28 00 00 00 bf c0 00 00 02 00
[ 335.369878] end_request: I/O error, dev sr1, sector 196352
[ 335.369884] Buffer I/O error on device sr1, logical block 49088
[ 335.369888] Buffer I/O error on device sr1, logical block 49089
[ 335.412879] ISO 9660 Extensions: Microsoft Joliet Level 3
[ 335.415877] sr 6:0:0:1: [sr1] Unhandled sense code
[ 335.415883] sr 6:0:0:1: [sr1] Result: hostbyte=DID_ERROR driverbyte=DRIVER_SENSE
[ 335.415887] sr 6:0:0:1: [sr1] Sense Key : Hardware Error [current]
[ 335.415892] sr 6:0:0:1: [sr1] Add. Sense: No additional sense information
[ 335.415897] sr 6:0:0:1: [sr1] CDB: Read(10): 28 00 00 00 bf fa 00 00 02 00
[ 335.415906] end_request: I/O error, dev sr1, sector 196584
[ 335.415912] Buffer I/O error on device sr1, logical block 49146
[ 335.415916] Buffer I/O error on device sr1, logical block 49147
[ 335.423852] sr 6:0:0:1: [sr1] Unhandled sense code
[ 335.423857] sr 6:0:0:1: [sr1] Result: hostbyte=DID_ERROR driverbyte=DRIVER_SENSE
[ 335.423861] sr 6:0:0:1: [sr1] Sense Key : Hardware Error [current]
[ 335.423866] sr 6:0:0:1: [sr1] Add. Sense: No additional sense information
[ 335.423870] sr 6:0:0:1: [sr1] CDB: Read(10): 28 00 00 00 bf fa 00 00 02 00
[ 335.423879] end_request: I/O error, dev sr1, sector 196584
[ 335.423885] Buffer I/O error on device sr1, logical block 49146
[ 335.423889] Buffer I/O error on device sr1, logical block 49147
[ 335.434846] sr 6:0:0:1: [sr1] Unhandled sense code
[ 335.434852] sr 6:0:0:1: [sr1] Result: hostbyte=DID_ERROR driverbyte=DRIVER_SENSE
[ 335.434856] sr 6:0:0:1: [sr1] Sense Key : Hardware Error [current]
[ 335.434861] sr 6:0:0:1: [sr1] Add. Sense: No additional sense information
[ 335.434865] sr 6:0:0:1: [sr1] CDB: Read(10): 28 00 00 00 bf fe 00 00 01 00
[ 335.434874] end_request: I/O error, dev sr1, sector 196600
[ 335.434888] Buffer I/O error on device sr1, logical block 49150
[ 335.435517] ISOFS: changing to secondary root
[ 335.444848] sr 6:0:0:1: [sr1] Unhandled sense code
[ 335.444853] sr 6:0:0:1: [sr1] Result: hostbyte=DID_ERROR driverbyte=DRIVER_SENSE
[ 335.444858] sr 6:0:0:1: [sr1] Sense Key : Hardware Error [current]
[ 335.444862] sr 6:0:0:1: [sr1] Add. Sense: No additional sense information
[ 335.444867] sr 6:0:0:1: [sr1] CDB: Read(10): 28 00 00 00 bf fe 00 00 01 00
[ 335.444876] end_request: I/O error, dev sr1, sector 196600
[ 335.444881] Buffer I/O error on device sr1, logical block 49150
[ 335.459849] sr 6:0:0:1: [sr1] Unhandled sense code
[ 335.459854] sr 6:0:0:1: [sr1] Result: hostbyte=DID_ERROR driverbyte=DRIVER_SENSE
[ 335.459859] sr 6:0:0:1: [sr1] Sense Key : Hardware Error [current]
[ 335.459863] sr 6:0:0:1: [sr1] Add. Sense: No additional sense information
[ 335.459868] sr 6:0:0:1: [sr1] CDB: Read(10): 28 00 00 00 bf fe 00 00 01 00
[ 335.459877] end_request: I/O error, dev sr1, sector 196600
[ 335.487845] sr 6:0:0:1: [sr1] Unhandled sense code
[ 335.487850] sr 6:0:0:1: [sr1] Result: hostbyte=DID_ERROR driverbyte=DRIVER_SENSE
[ 335.487854] sr 6:0:0:1: [sr1] Sense Key : Hardware Error [current]
[ 335.487859] sr 6:0:0:1: [sr1] Add. Sense: No additional sense information
[ 335.487864] sr 6:0:0:1: [sr1] CDB: Read(10): 28 00 00 00 bf fe 00 00 01 00
[ 335.487872] end_request: I/O error, dev sr1, sector 196600
[ 335.495848] sr 6:0:0:1: [sr1] Unhandled sense code
[ 335.495853] sr 6:0:0:1: [sr1] Result: hostbyte=DID_ERROR driverbyte=DRIVER_SENSE
[ 335.495857] sr 6:0:0:1: [sr1] Sense Key : Hardware Error [current]
[ 335.495862] sr 6:0:0:1: [sr1] Add. Sense: No additional sense information
[ 335.495866] sr 6:0:0:1: [sr1] CDB: Read(10): 28 00 00 00 bf fe 00 00 01 00
[ 335.495875] end_request: I/O error, dev sr1, sector 196600
[ 335.504054] sr 6:0:0:1: [sr1] Unhandled sense code
[ 335.504059] sr 6:0:0:1: [sr1] Result: hostbyte=DID_ERROR driverbyte=DRIVER_SENSE
[ 335.504063] sr 6:0:0:1: [sr1] Sense Key : Hardware Error [current]
[ 335.504068] sr 6:0:0:1: [sr1] Add. Sense: No additional sense information
[ 335.504073] sr 6:0:0:1: [sr1] CDB: Read(10): 28 00 00 00 bf fe 00 00 01 00
[ 335.504081] end_request: I/O error, dev sr1, sector 196600
[ 335.516068] sr 6:0:0:1: [sr1] Unhandled sense code
[ 335.516073] sr 6:0:0:1: [sr1] Result: hostbyte=DID_ERROR driverbyte=DRIVER_SENSE
[ 335.516077] sr 6:0:0:1: [sr1] Sense Key : Hardware Error [current]
[ 335.516082] sr 6:0:0:1: [sr1] Add. Sense: No additional sense information
[ 335.516087] sr 6:0:0:1: [sr1] CDB: Read(10): 28 00 00 00 bf fe 00 00 01 00
[ 335.516095] end_request: I/O error, dev sr1, sector 196600
[ 335.523851] sr 6:0:0:1: [sr1] Unhandled sense code
[ 335.523854] sr 6:0:0:1: [sr1] Result: hostbyte=DID_ERROR driverbyte=DRIVER_SENSE
[ 335.523859] sr 6:0:0:1: [sr1] Sense Key : Hardware Error [current]
[ 335.523863] sr 6:0:0:1: [sr1] Add. Sense: No additional sense information
[ 335.523868] sr 6:0:0:1: [sr1] CDB: Read(10): 28 00 00 00 bf ee 00 00 02 00
[ 335.523877] end_request: I/O error, dev sr1, sector 196536
[ 335.531846] sr 6:0:0:1: [sr1] Unhandled sense code
[ 335.531850] sr 6:0:0:1: [sr1] Result: hostbyte=DID_ERROR driverbyte=DRIVER_SENSE
[ 335.531855] sr 6:0:0:1: [sr1] Sense Key : Hardware Error [current]
[ 335.531859] sr 6:0:0:1: [sr1] Add. Sense: No additional sense information
[ 335.531864] sr 6:0:0:1: [sr1] CDB: Read(10): 28 00 00 00 bf fc 00 00 02 00
[ 335.531873] end_request: I/O error, dev sr1, sector 196592
[ 335.539848] sr 6:0:0:1: [sr1] Unhandled sense code
[ 335.539854] sr 6:0:0:1: [sr1] Result: hostbyte=DID_ERROR driverbyte=DRIVER_SENSE
[ 335.539858] sr 6:0:0:1: [sr1] Sense Key : Hardware Error [current]
[ 335.539863] sr 6:0:0:1: [sr1] Add. Sense: No additional sense information
[ 335.539867] sr 6:0:0:1: [sr1] CDB: Read(10): 28 00 00 00 bf fe 00 00 01 00
[ 335.539876] end_request: I/O error, dev sr1, sector 196600
[ 335.547848] sr 6:0:0:1: [sr1] Unhandled sense code
[ 335.547854] sr 6:0:0:1: [sr1] Result: hostbyte=DID_ERROR driverbyte=DRIVER_SENSE
[ 335.547858] sr 6:0:0:1: [sr1] Sense Key : Hardware Error [current]
[ 335.547863] sr 6:0:0:1: [sr1] Add. Sense: No additional sense information
[ 335.547867] sr 6:0:0:1: [sr1] CDB: Read(10): 28 00 00 00 bf fe 00 00 01 00
[ 335.547876] end_request: I/O error, dev sr1, sector 196600
[ 335.555850] sr 6:0:0:1: [sr1] Unhandled sense code
[ 335.555856] sr 6:0:0:1: [sr1] Result: hostbyte=DID_ERROR driverbyte=DRIVER_SENSE
[ 335.555860] sr 6:0:0:1: [sr1] Sense Key : Hardware Error [current]
[ 335.555865] sr 6:0:0:1: [sr1] Add. Sense: No additional sense information
[ 335.555869] sr 6:0:0:1: [sr1] CDB: Read(10): 28 00 00 00 bf fc 00 00 01 00
[ 335.555878] end_request: I/O error, dev sr1, sector 196592
[ 335.563845] sr 6:0:0:1: [sr1] Unhandled sense code
[ 335.563850] sr 6:0:0:1: [sr1] Result: hostbyte=DID_ERROR driverbyte=DRIVER_SENSE
[ 335.563854] sr 6:0:0:1: [sr1] Sense Key : Hardware Error [current]
[ 335.563859] sr 6:0:0:1: [sr1] Add. Sense: No additional sense information
[ 335.563863] sr 6:0:0:1: [sr1] CDB: Read(10): 28 00 00 00 bf fd 00 00 01 00
[ 335.563871] end_request: I/O error, dev sr1, sector 196596

Verze OS:
Linux nyklesovi-desktop 2.6.32-46-generic #105-Ubuntu SMP Fri Mar 1 00:08:49 UTC 2013 i686 GNU/Linux

Verze modemu:
ZyXel model no.401380..

Snad jsem napsala všechno :)

Modem pripojeny mas, system ho spravne vidi a rozoznava.
V sietovej konfiguracii ti chyba nazov interface a k nemu priradena IP adresa aby mohol system komunikovat s USB modemom. To, ze chyba nazov interface moze byt tym, ze sa nezaviedol ovladac.
Este existuje moznost, ze ovladac je zavedeny, akurat sa zmenil nazov interface na iny (napriklad eth0 sa zmenilo na usb0) a NetworkManager si zmenu nevsimol.

Vyskusaj poprezerat nastavenie NetworkManagera ci neobjavis chybu.

Pre zistenie ci existuje ovladac by bolo potrebne vykonat prikaz: lsmod
a este prikaz: ip addr show

Z toho moc moudrá nejsem.. :
Module Size Used by
tda1004x 15070 1
saa7134_dvb 22167 0
videobuf_dvb 5175 1 saa7134_dvb
dvb_core 86206 1 videobuf_dvb
saa7134_alsa 10380 1
binfmt_misc 6523 1
snd_hda_codec_realtek 203472 1
fbcon 35102 71
tileblit 1999 1 fbcon
font 7557 1 fbcon
bitblit 4707 1 fbcon
softcursor 1189 1 bitblit
vga16fb 11385 0
vgastate 8961 1 vga16fb
tda827x 9240 2
rndis_wlan 20617 0
cfg80211 126496 1 rndis_wlan
tda8290 12092 1
tuner 20412 1
snd_hda_intel 22069 1
snd_hda_codec 74297 2 snd_hda_codec_realtek,snd_hda_intel
snd_hwdep 5412 1 snd_hda_codec
snd_pcm_oss 35308 0
snd_mixer_oss 13746 1 snd_pcm_oss
snd_pcm 70694 4 saa7134_alsa,snd_hda_intel,snd_hda_codec,snd_pcm_oss
snd_seq_dummy 1338 0
snd_seq_oss 26722 0
snd_seq_midi 4557 0
snd_rawmidi 19056 1 snd_seq_midi
snd_seq_midi_event 6003 2 snd_seq_oss,snd_seq_midi
rndis_host 5756 1 rndis_wlan
cdc_ether 3541 1 rndis_host
snd_seq 47263 6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event
saa7134 143423 2 saa7134_dvb,saa7134_alsa
usbnet 14975 3 rndis_wlan,rndis_host,cdc_ether
nouveau 467048 2
snd_timer 19130 2 snd_pcm,snd_seq
snd_seq_device 5700 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq
ir_common 38875 1 saa7134
ttm 49847 1 nouveau
v4l2_common 15431 2 tuner,saa7134
drm_kms_helper 29329 1 nouveau
mii 4381 1 usbnet
ppdev 5259 0
videodev 34457 3 tuner,saa7134,v4l2_common
v4l1_compat 13251 1 videodev
snd 54244 17 saa7134_alsa,snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
drm 163779 4 nouveau,ttm,drm_kms_helper
videobuf_dma_sg 10782 3 saa7134_dvb,saa7134_alsa,saa7134
parport_pc 25962 1
psmouse 63677 0
serio_raw 3978 0
videobuf_core 16356 3 videobuf_dvb,saa7134,videobuf_dma_sg
tveeprom 11102 1 saa7134
soundcore 6620 1 snd
snd_page_alloc 7076 2 snd_hda_intel,snd_pcm
agpgart 31724 2 ttm,drm
i2c_algo_bit 5028 1 nouveau
k8temp 3152 0
i2c_nforce2 5199 0
lp 7060 0
parport 32635 3 ppdev,parport_pc,lp
floppy 53016 0
pata_amd 8766 0
forcedeth 49556 0
sata_nv 19376 2

A na IP :

1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN qlen 1000
link/ether 00:16:17:76:97:f4 brd ff:ff:ff:ff:ff:ff
3: eth1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN qlen 1000
link/ether 00:13:49:cc:88:27 brd ff:ff:ff:ff:ff:ff

Já na to teď ještě koukám, ale asi toho moc nevykoukám.. :)

Mas tam dva nenakonfigurovane interface.
Predpokladam, ze tam nemas 2 LAN karty.
Jeden iface bude pravdepodobne od toho modemu a je mozne ze navzajom prehodili ked si odstranila USB modem a system nabehol bez toho modemu.
V NetworkManager odobrat vsetky iface a znova nakonfiguravovat by mohlo pomoct.

pripadne vyskusaj ci bude niektory spravne reagovat na nahodenie pomocou:
ifconfig ethX up
dhclient ethX

Dvě LAN karty nemám :). Zkoušela jsem ty příkazy a psalo mi to, že operace byla zamítnuta.. takže ještě chci zkusit znovu všechno nakonfigurovat.

Možná to bude znít hloupě, ale nejde mi najít v grafickým prostředí networkmanager a nejde to nakonfigurovat znovu ani podle příkazů. (i když tady může být chyba ve mě)